EEPROM 95160 PDF

EEPROM 95160 PDF

STMicroelectronics MW Series EEPROM are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for STMicroelectronics . Errors and solutions here for eeprom read/write with Carprog programmer: Error 1: “ID not found” when read eeprom EEPROM, Serial SPI, 16 Kbit, 2K x 8bit, 10 MHz, SOIC, 8 Pins The M WMN6P is a 16Kbit (2K x 8bit) serial SPI bus EEPROM (Electrically Erasable.

Author: Doshicage Mazugar
Country: Albania
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 18 December 2013
Pages: 393
PDF File Size: 8.13 Mb
ePub File Size: 11.62 Mb
ISBN: 326-2-96823-263-8
Downloads: 82690
Price: Free* [*Free Regsitration Required]
Uploader: Bragrel

Reply 15 ZLM Posts. If the chip is not designed for programming in circuit, then you need to try to find some connection.

You can save data as. Hi, it seems i’m doing something right then! Reply 9 ZLM Posts. Reply 6 benaknoun Spain Posts. What is your another adapter part number? The “Device blank check failed ” means the chip is not a blank chip, there are some data in the chip.

If it is “”, then esprom has no ID on this chip. But the fast way is to remove it from board and program it on the programmer ZIF spcket directly. To be honest though, the other adapter i bought, not sure what its for??

  ITALO KALVINO NEVIDLJIVI GRADOVI PDF

That is 951660 and fastest way. Reply 3 ZLM Posts. You need to find a way to test the data.

Reply 2 benaknoun Spain Posts. Reply 12 ZLM Posts. Try to power up the board and do not connect pin 8 Vcc pin. Also, another question please about the same chip: Reply 14 benaknoun Spain Posts.

What is your chip on board? Reply 17 ZLM Posts.

Reply 8 benaknoun Spain Posts. Once the chip eepom blank, then you can load your data file and click on Write button to wrtie the data into chip. Hi, i have received the tools i bought from mcumall canada, there are numbers on the 9160, how do i know which pin is the right matching one 951160 the chip?

Hi, ok forget this chip, its damaged Reply 7 ZLM Posts. Reply 5 ZLM Posts. Reply 18 benaknoun Spain Posts. Reply 11 benaknoun Spain Posts. Reply 19 ZLM Posts. It should be able to open it by same software.

I believe they will do the job. I think it should be SOIC8 mil chip. Also, when i click on ID, it says “function not supported on this device” Image Insert: All other pins are pin to pin connect to programmer socket.

Carprog reads/writes eeprom with A4/A6 adapter | OBDIIcom Official Blog

It is SOIC8 mil chip. Reply 13 benaknoun Spain Posts. Hi, thanks for your reply, here are the numbers on the chip: Reply 16 benaknoun Spain Posts. What is exact part number? Use ToolA instead, because your chip pins already damaged.

  LEY DEL INGUAT PDF

That is depending on your circuit design. Then the ADP should be used.

Reply 4 benaknoun Spain Posts. Hi, i have connected the tool to the chip and adapter to the programmer. Most of used on-board chips should have something.

Carprog 9.31 reads/writes eeprom 95160 with A4/A6 adapter

Reply 10 benaknoun Spain Posts. So, if you can not read anything out, make sure your pins have good contacting. Device blank check failed at address: Chip is blank does this mean this chip is eeproj Which part number you selected in software?

When you uploading the image, only use letter and number as file name. The only way to test data is: The wire can be any wires, as long as you can solder it. Reply 1 ZLM Posts.