E/ECE/ E/ECE/TRANS/ } Rev.1/Add/Rev Regulation No. 48 page 3. Regulation No. UNIFORM PROVISIONS CONCERNING. Regulation No 48 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of vehicles with. Regulation No 48 of the Economic Commission for Europe of the United Nations (UNECE) — Uniform provisions concerning the approval of.
|Published (Last):||21 June 2016|
|PDF File Size:||3.52 Mb|
|ePub File Size:||11.18 Mb|
|Price:||Free* [*Free Regsitration Required]|
InterRegs: Regulation No. | ECE – United Nations
These tests will be on samples selected at random without causing distortion of the manufacturers delivery commitments. The position, as regards width, will be determined from that edge of the apparent surface in the direction of the reference axis which is the furthest from the median longitudinal plane of the vehicle when referred to the overall width, and from the inner edges of the apparent surface in the direction of the reference axis when referred to the distance between lamps.
Optional on vehicles between 1. Examples of apparent surface based on illuminating surface in different directions of geometric visibility. Where a vehicle is fitted with four concealable headlamps the installation of two additional headlamps shall only be authorised for the purpose of light-signalling, consisting of intermittent illumination, at short intervals see paragraph 5.
W 12 blue boundary: Amber or red Rear-end collision alert signal: The vehicle shall have the parking brake released and the gearbox in neutral. The SM1 type of side-marker lamp shall be used on all categories of vehicles; however the SM2 type of side-marker lamps may be used on the M 1 category of vehicles. The number of positions on devices which are not continuously adjustable shall be such as to ensure compliance with the range of values prescribed in paragraph 6.
The lamps that are grouped or combined with or reciprocally incorporated in the AFS; 3.
Regulation 49 – 06 series (click to expand)
This lamp is intended, for sce vehicles and trailers, to complement the vehicle’s front and rear position lamps by drawing particular attention to its bulk; 2. Of service-door lighting systems on vehicles of Categories M and M as specified in Paragraph 2.
Other Requirements The functioning of this lamp may also be performed by simultaneously switching on the front and rear position lamps on the same side of the vehicle. A line marking may be installed instead of the mandatory contour marking if the shape, structure, design or operational requirements of the vehicle make it impossible to install the mandatory contour marking.
Of devices for indirect vision; 2. Front fog lamp levelling device 6. In the absence of specific instructions lamps constituting a pair shall: For S3 or S4 categories devices: Any temporary fail-safe replacement of the light-signalling function of a rear position lamp is allowed, provided that the replacement function in case of a failure is similar in colour, main intensity and position to the function that has ceased to operate and provided that the replacement device remains operational in its original safety function.
No point on the apparent surface in the direction of the reference axis must be higher than the highest point on the apparent surface in the direction of the reference axis of the dipped-beam headlamp. Position No individual specifications.
Most countries, even if not formally participating in the agreement, recognise the UN Regulations and either mirror the UN Regulations’ content in their own national requirements, or d48 the import, registration, and use f48 UN type-approved vehicles, or both. The means of controlling the maximum voltage at the terminals of the device may, for convenience, be located within the body of the device. Red Front retro-reflector, non-triangular: As from 66 months for new vehicles type of categories M 1 and N 1 and 84 months for new vehicles type of other categories after the official date of entry into force of the 05 series of amendments to this Regulation, Contracting Parties applying this Regulation shall grant approvals only if the new vehicle type to be approved meets the requirements of this Regulation as amended by the 05 series of amendments excluding paragraphs 6.
For S3 or S4 Category Devices: For the distance in between the inner edges of the apparent surfaces in the direction of the reference axes there is no special requirement. Moreover, the electrical connections of the two optional devices mentioned in paragraph 6.
As from 36 months from the entry into force of Supplement 3 to the 04 series of amendments, Contracting Parties applying this Regulation shall grant approvals only if the vehicle type to be approved meets the requirements of the paragraphs 3.
EUR-Lex – X(03) – EN – EUR-Lex
SY 12 green boundary: Only dipped-beam headlamps according to Regulation No 98 or may be used to produce bend lighting. E48 direction indicator lamps, the interdependent lamp s specified by the Applicant during the device approval procedure shall meet all the position, geometric visibility, photometric and colorimetric requirements at all fixed positions of the movable component s.
If the distance between the front direction-indicator lamp and the daytime running lamp is equal or less than 40mm, the electrical connections of the daytime running lamp on the relevant side of the vehicle may be such that either: The r84 obtained shall be such that the requirement in paragraph 6.
This may be demonstrated by the manufacturer by calculation or by other means accepted by the authority responsible for type approval.